Silver Double Din Dash Complete Kit Install Car Radio Stereo Fits PT Cruiser

Description

Double Din Dash Kit for
Chrysler PT Cruiser 2006-2010
This dash kit provides an easier and cheaper option for installing a new aftermarket radio. Before this kit you would have to get a custom kit built which costs upwards of 0.
Included:
Dashboard Bezel
Mounting Brackets
Standard Wiring Harness
Antenna Adapter
Instructions via email
Dash Kit Description:
Radio opening measurements are approximately 6 7/8 inches by 3 7/8 inches.
Converts factory opening to accommodate a Double Din Aftermarket Radio.
Brackets are vehicle specific and align with factory mounting.
Designed to have a seamless contoured fit in dashboard.
Factory matched Silver and factory matched texture.
Solid one piece ABS Plastic construction.
Special Notes:
Wire Harness will NOT retain steering wheel controls
Wire Harness will NOT work on vehicle with Rear Tuners
Wire Harness is compatible with STANDARD WIRING only
Email us if you have Premium Sound System for the right kit
Wire Harness will NOT work on vehicles with Factory Infinity Systems or Factory Boston Acoustic System
Wire Harness will NOT work on vehicles with Factory CAN Bus Radios models REF, REC, RAQ or RAK (name can be found on the face of the radio)
EIA Color Codes:
Yellow – 12V Constant
Red – 12V Accessory
Black - Ground
Black with White Stripe - Factory Amplifier Ground
Blue - Power Antenna /
Factory Amplifier Remote Turn On
Blue with White Stripe - Factory Amplifier Remote Turn on
Orange – Dash Light Dimmer/Illumination
Orange with White Stripe - Dash Light Dimmer/Illumination
Brown - Mute / Not Used
Green – Left Rear Speaker (+)
Green with Black Stripe Left Rear Speaker (-)
White – Left Front Speaker (+)
White with Black Stripe – Left Front Speaker (-)
Purple – Right Rear Speaker (+)
Purple with Black Stripe – Right Rear Speaker (-)
Gray – Right Front Speaker (+)
Gray with Black Stripe – Right Front Speaker (-)
Installation Directions:
You can also Google " Pt Cruiser a/c radio removal "
Step 1: Remove the 2 a/c vent screws- There are two screws, one in each A/C vent. Rotate the vent until the vanes are exactly horizontal. You should be able to see a notch in the bottom center inside the vent. If you can't see it, rotate the vent around 180 degrees. The screw is a black standard Phillips head and isn't the easiest thing to see in the dark. A flashlight can help. A magnetic screwdriver helps to get them out of the vents.
Step 2: Remove Factory bezel- There are 9 press fittings holding the bezel in place. There are two at the top (above the vents) , two on the sides (even with the vents), two on the sides of the radio (even with the radio), two on the sides below the a/c controls, and one centered at the bottom. I started at the bottom and using a slow steady force pulled the bezel loose  (at the button of the bezel there are two notches that you can use a flat head and ply back on) , then work your way all the way around the bezel. .
Step 3: Unplug factory controls-Unplug window controls, hazard switch, Clock and unhook a/c cables- Start at the top. Remove the clock cable by pressing down on the release on the plug on the bottom side and pulling the plug out. Next is the power windows cable. There is a red plastic lock on this plug. The lock is pushed upward (not away!) from the bottom side of the plug to release it. Once unlocked, the release tab on the right side is pressed and the plug can be pulled out. The defroster-hazard cluster cable comes out the same way as the clock cable. Next remove the heater cables.
Step 4: Remove The Factory Radio- Four torx screws on the corners hold the radio in place. Use a T-15 torx head driver. The radio comes right out. There are three cables on the back: the antenna wire and the two radio harness plugs. The harness plugs each have a press release on the top while the antenna wire just pulls out.
Step 5: Remove components from factory bezel- Remove the a/c vents and controls (a/c vents have 3 screws each and the controller has 4, save these they will be reused) from factory bezel using a Phillips head. Unsnap the window controls and defroster-hazard cluster.
Step 6: Reinstall everything that you just removed from the factory bezel to the new aftermarket bezel.
Step 7: Mount brackets-Next secure the supplied double din brackets to the new aftermarket bezel using supplied screws.
Step 8: Mount the aftermarket radio to the brackets ( using the supplied screws that came with your aftermarket radio) , leave the screws loose. Adjust the depth of the radio until it sits perfectly flush (or where you like it) with the front bezel face. Then tighten down the screws.
Step 9: Wire the aftermarket radio harness to the harness supplied using butt connectors or solder wiring together .
Step 10: Plug in aftermarket radio harness to aftermarket radio & install harness to factory radio plug. Plug in all factory controls and reconnect a/c cables.
Step 11: Connect antenna adapter to factory antenna end & aftermarket radio.
Step 12: Snap main dash bezel back into dash.
Step 13: Install screws into a/c vents that retain the dash
--------------------------------------------------------------------------------------------------------------------
General Policies
At Autoware we strive to offer you the best pricing, quick shipping and fast customer service for all your aftermarket needs.
If you have any questions about a part please contact us before purchasing. We want to ensure that you are buying the right product to avoid the hassle of returning or exchanging. We generally respond to our emails 7-days a week.
Shipping and Billing
We only accept payment from confirmed PayPal addresses.
We typically ship to most countries, as well as the United States and Canada. If you have any questions or concerns about your location please email us. International rate do apply for shipping out of the United States.
We will ship packages same day as long as they are ordered and paid for before 8:00 AM EST. If purchased after this time the order will ship next business day. Our business days are Monday thru Friday excluding any federal holidays.
Returns
We will take responsibility for damage upon arrival or defective parts. Please email us immediately to notify us that there is a problem.
If the customer purchased the wrong item or decides that the item is no longer needed a refund will be provided minus 20% restocking fee and return shipping will be paid by the customer.
All other returns or exchanges are personally analyzed and resolved by our team.